Your Plumbing Crash Course: Tips for Installing a Bathtub

Quote

What are your opinions about Tools You Need to Install a New Bathtub ?


How to Install a Bathtub
Installing a bath tub isn't specifically brain surgery, however it does need solid plumbing, carpentry, and also in some cases, tiling skills. Changing an old bath tub with a new one is also a reasonably tough job. If the old bathtub is easily available, the task can move speedily; if you need to open up a wall surface to eliminate the old tub and position the new bathtub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require an assistant to leave the old tub and set in the brand-new one. Make sure you have actually qualified yourself for the job and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed task, it is better to consider utilizing one before you begin. Possibilities are you may require an expert plumber to make tube connections.
This write-up will certainly aid you set up a brand-new bathtub in your washroom if you have currently acquired a brand-new tub and also don't require to transform the arrangement of your previous water supply pipes.
Your devices and also material checklist need to comprise the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Preparing for the Installation


    Firstly, the supporting frame supplied with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps unit to prevent stress on the bathtub.
    Fit the adaptable tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the provided washing machines.
    Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.

    Removing Old Touches


    If you need to change old taps with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any water remaining in the system. The procedure of removing the existing taps can be fairly bothersome because of the limited accessibility that is often the case.
    Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. When the supply pipelines have actually been removed, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old securing compound.
    Prior to carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new taps to fit.

    Installing the Bathtub


    Using both wood boards under its feet, place the tub in the needed setting. The wooden boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
    The following goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the level checks out degree.
    To set up faucets, fit the bottom of the outermost versatile faucet connector to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
    Activate the water system and inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill up the tub as well as also inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
    Finally, repair the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the bathtub ought to wait up until the tub has been utilized a minimum of once as this will settle it right into its last setting.

    Fitting New Taps


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end offers a connection to the current supply pipes.
    If you require to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
    Next off, place the faucet in the placing hole in the bath/basin making certain that the washing machines are in place between the faucet as well as the sink. Secure the tap in place with the manufacturer provided backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be linked to the tap ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Tiling Around the Tub


    In the area where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack an inflexible seal, triggering the water to permeate the wall surface in between the bath and the tiling, leading to issues with dampness and also possible leakages to the ceiling listed below.
    You can select from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this motion prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently offered on the market. It is recommended to fit the tiles utilizing waterproof or water-proof sticky as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub

    As a passionate reader about Tools You Need to Install a New Bathtub , I assumed sharing that blog post was essential. Are you aware of another individual who is intrigued by How to Install a Bathtub Yourself? Do not hesitate to promote it. Bless you for your time. Please check our website back soon.


    Expertise? One call away.

    Leave a Reply

    Your email address will not be published. Required fields are marked *